circle-radius-waterjet-cutter0 pages
r
nnnnWATERJET SYSTEMS
nnnnSPYDER ABRASIVE JET
nnnnCIRCLE £t RADIUS
nnnnCUTTING SYSTEM
nnnnA Cut Above
nnnnSuitable for any environment:
nnnn• Cuts virtually any material without heat or flames
nnnn• Pneumatic reversible drive motor
nnnn• Non-ferrous motion components
nnnnEasy Set Up:
nnnn• Self-aligning
nnnn• Lighweight suction cup mount
nnnnAvailable in two sizes:
nnnn• 1 "-6.5"insider diameter/16"-48"outside diameter
nnnn• 3"-12.5"inside diameter/27.5"-56"outside diameter
nnnnMovement Speed:
nnnnVaries due to several ranges of gear reducers
nnnnOptional Linear and Pipe Cutting Tracks:
nnnn• 3,5 and 10 linear-foot tracks
nnnn• Low profile, rigid and vacuum tracks available
nnnn• Pipe track: 6-60 inches (152-1524 mm)
nnnnMaster Control Station
nnnn• Three-position directional valve for pneumatic drive unit
nnnn• Dual air regulators for directional speed control
nnnn• Control abrasive flow from console
nnnn• One palm button shuts off UHP water and abrasives
nnnnVacuum Generator
nnnn• Steel construction
nnnn• Pneumatic control vacuum
nnnn• Locking quick disconnects
nnnn• Lightweight compact design
nnnnHead Manipulator
nnnn• Drive unit adapts for use with track or pipe cutting bands
nnnn• Pneumatic reversible drive motor with interchangeable gear drive
nnnn• Precise speed control for accurate cutting feed rates
nnnn• Center line mounting of abrasive cutting head
nnnn• Adjustable angle for beveling cuts
nnnnPermalign II Abrasive Head
nnnnLength 10.94 in (27.8 cm)
nnnnWeight 4 lbs (1.8 kg)
nnnnOperating air pressure (min) 60 psi (4 bar)
nnnnWater pressure (max) 60,000 psi (4100 bar)
nnnnOrifice range .005 - .021 in (.127 - .53 mm)
nnnnNozzle range .020 - .065 ID (.508 - 1.65 mm)
nnnnMax flow rate 2.1 gpm (7.95 Ipm)
nnnnHigh Flow Abrasive Head (for cutting thicker
nnnnmaterial or multiple layers)
nnnnLength 7.55 in (19.1 cm)
nnnnWeight 4.00 lbs (1.8 kg)
nnnnOperating air pressure (min) 60 psi (4 bar)
nnnnWater pressure (max) 45,000 psi (3100 bar)
nnnnOrifice range .020 - .036 in (.51 - .91 mm)
nnnnNozzle range .095 - .125 ID (2.41 - 3.18 mm)
nnnnMax flow rate 5.1 gpm (19.04 Ipm)
nnnnAbrasive Delivery System
nnnn• Lightweight durable high-impact poly design
nnnn• Two-wheel pneumatic tires with rigged frame
nnnn• Air-regulated metering valve
nnnn• Delivery rate: up to 3 lb (1.36 kg)/minute
nnnnDesigned for use in remote and potentially
nnnnhazardous environments. Jet Edge's Spyde
nnnnAbrasivejet Radius and Circle Cutting Syste
nnnncan be set up on the side of tanks, small
nnnnvessels and large diameter piping. It is held
nnnnin place by vacuum cups and features a
nnnnself-aligning centering pin for fast and
nnnnreliable setup. Motion components are
nnnnmade from non-ferrous materials, and
nnnncutting head manipulators are powered by
nnnnpneumatic motors, making the Spyder
nnnnsuitable for use in all environments.
nnnnA master control panel allows operators to control the cutting head manipulators,
nnnndirection, speed of travel, abrasive delivery and vacuum components from one
nnnnlocation.
nnnnPOWERED BY JET EDGE!
nnnnThe Riding Deckblaster
nnnnis powered by a
nnnnJet Edge waterjet
nnnnintensifier pump.
nnnn□1 www.jetedge.com
nnnn+ 1-763-497-8700| 1 -800-JET-EDGE
nnnnsales@jetedge.com
nnnnMADE IN THE
nnnn12070 43rd St. N.E. St. Michael, MN 55376 USA IJSJ^
"