"

1 KHS INNOPET® BLOMAX SERIES IV

nnnn

STRETCH BLOW MOLDING MACHINES

nnnn

PET PACKAGING SOLUTIONS

nnnn

m

nnnn

The InnoPET Blomax Series IV has an output

nnnn

rate of up to 72,000 PET bph. The InnoPET

nnnn

Blomax Serles IV Is available In a modular

nnnn

design of 4 to 36 blowing stations, each

nnnn

with an output rate of up to 2,200 PET bph

nnnn

The standard production of the InnoPET

nnnn

Blomax Serles IV Is a bottle volume of 0.2 to

nnnn

3.0 liters. Special sizes can also be produced

nnnn

During the development of all technlca

nnnn

nnovatlons within the InnoPET Blomax

nnnn

Serles IV, special emphasis was placed on

nnnn

key requirements like minimum energy

nnnn

consumption, process stability as well as

nnnn

uptime. The focus and goal of the develop-

nnnn

ment were lowest total cost of ownership

nnnn

per produced bottle. All technical Inno-

nnnn

vations Integrated Into the Serles IV support

nnnn

this goal

nnnn

The new NIR Reflexx-oven

nnnn

• Exclusive use of short-wave, energy-dense

nnnn

NIR (Near Infra Red) radiation

nnnn

• Heatlng-up time of preforms reduced by 50%

nnnn

• Reduction of surface heat

nnnn

• Re-heat and cooling energy consumption

nnnn

reduced by approx. 30% vs. traditional

nnnn

heating technology

nnnn

The new CLever-Loc blow molding stations

nnnn

• minimum footprint design, more stations

nnnn

on the same blowing wheel diameter

nnnn

• only one half opens, the other half

nnnn

remains rigid

nnnn

• CLever-Loc device, clamping through toggle

nnnn

• Longer process time

nnnn

• Higher specific output of up to

nnnn

2,200 bottles/h/statlon

nnnn

• Compatible with Series III molds

nnnn

Preform transport via active mandrel and

nnnn

TouchGrip system

nnnn

• Improvement of the established mandrel

nnnn

system: Active mandrel transports preforms

nnnn

gently and securely through the oven

nnnn

• Smallest pitch, 37.7 mm

nnnn

• Gripper of TouchGrip systems take over

nnnn

preforms

nnnn

Servo-driven StretchFlexx

nnnn

stretching system

nnnn

• Stretching speed Independent of

nnnn

machine speed

nnnn

• Servomotors control the stretching rod

nnnn

• Rapid change-over, no mechanica

nnnn

adjustment

nnnn

• Stretching movement and -speed can be

nnnn

adjusted on the screen

nnnn

• High process stability

nnnn

• Less scrap

nnnn

Compressed air savings with

nnnn

Eco-Space valves

nnnn

• Approx. 15% decrease of top Industria

nnnn

values In compressed air consumption

nnnn

through redesign of valve block

nnnn

• Approx. 25-30% savings of blowing air

nnnn

through reduced dead air volume

nnnn

• Alrback air recycling Internally or externally

nnnn

Low maintenance

nnnn

• Reduction of wear parts

nnnn

• Central axis of blowing station with

nnnn

permanent lubrication

nnnn

• Automatic central lubrication

nnnn

• No adjustment of guldlngs and transfers

nnnn

• Large doors, easy accessibility

nnnn

Availability

nnnn

• Up to 25% savings In change-over time

nnnn

of blowing stations

nnnn

• Run-up time only approx. 15 sec

nnnn

More efficiency in blocked systems

nnnn

• Easy Interlocking with suitable fillers/caps

nnnn

to an InnoPET BloFIII block

nnnn

• Short start-up time

nnnn

• 50% less preform scrap after

nnnn

emergency stop

nnnn

• Improved adaptation to filling output

nnnn

through Independent stretching

nnnn

• Enhanced product quality

nnnn

Important:

nnnn

Reference of all values is made in comparison to Series III

nnnn

/KHS

nnnn

Filling and Packaging - Worldwide

"