ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت Steriflow در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
-
Laboratory/process:
process
-
Other characteristics:
rotary
-
Sterilization method:
hot air
During all the heating phase , a fan is running to mix and make circulating the air/steam
In some application, a pre heating through vertical heat-exchanger plate may be necessary.
Then the heating phase can begin.
It is realized by direct steam injection inside the vessel. The steam injection ramp is mounted under the baskets. The scattering is done between each basket.
The steam modulating valve opening is controlled by the MPI, till the programmed temperature is reached (121°C for example).
The condensates are stored in the lower part of the vessel.
Once the programmed holding time is finished, a pre-cooling starts. It is done by cold water injection inside the internal exchangers.
It is combined with the condensates / make-up cold water mixture by recirculation of the condensates through the by-pass loop (no contact of this mixture with the load).
Once the programmed temperature is reached, for instance 90°C, the final cooling begins with recycled water spraid on the load.
The recycled water is composed of steam condensates accumulated during the previous phases as well as make-up water.
The mixture is pumped at the lower level of the sterilizer, goes through the secondary circuit of an external heat exchanger and through an adjustable valve (3 positions). Then it goes back into the vessel on several spraying ramps installed above the load to be cooled down.