ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت Herzog AG در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
-
Function:
cleaning
-
Function:
sprue for multiple injection
-
Media:
air
-
Other characteristics:
needle valve, pneumatic actuation
-
Other characteristics:
needle valve, spring operated
-
Stream:
multi-jet
Finds application in:
Packaging, automobile and leisure industries, medicinal and electronic equipment.
Operation:
The nozzle is opened directly from the injection pressure and closed again with spring power. A needle which moves axially in the needle shut-off nozzle is held in the closed position by the force of the spring. The nozzle orifice is normally closed. With the increasing melt pressure exerted against the spring through a ring of exposed surface area on the needle, the nozzle opens at 200 bar . If the melt pressure drops (below 80bar), the nozzle closes.
- If the standard opening pressure is not appropriate, the needle must be modified to the requirements (modification of the spring is not possible).
- A temperature resistant material (bis max. 520°C) is used for the spring construction.
- The nozzle size required depends on the injection rate per second (cm3/s).
Prevents:
• Stringing, drooling
• Air pockets during screw retraction
• Material leakage when dosing with a withdrawn injection unit
• Material leakage while vertically injecting
Productivity factors:
• Controlled, clean shut-off of the melt stream
• Shorter cycle times - increase in productivity
• Increased process reliability and repeatability
• Usability with increased back pressure - improved homogenization
• Quick machine installation
• Add-on capability (on tool side)
Option:
• Filter module