ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت TAPPEX در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
-
Applications:
for plastics
-
Drive type:
Frearson
-
Head:
pan head
-
Materials:
stainless steel
-
Other characteristics:
self-tapping
to be used in most thermoplastic materials. These screws can be installed
into drilled or moulded holes in a wide variety of applications.
Tappex TPX screws are produced by cold forging, not machined from bar or wire and
therefore have good inherent mechanical properties with minimum residual
stress material into which it is being installed.
Features
Range of diameters and thread lengths.
Philips or Recessed Star Drive.
Hardened steel with a zinc and clear passivate.
Stainless steel 303 grade.
30 degree thread flank angle offers the following benefits:
Reduced installation torque.
Reduced potential for over tightening.
Reduced stress induced in the plastic.
(care should be taken with notch sensitive plastics)
With care the TPX screw can be re-installed multiple times.
Thread Forming Screws
Design Considerations
For successful installation and application a number of factors should be taken into consideration:
Hole size and design - recommended hole geometry available from Tappex
(See ETP 45 downloadable from Tappex website)
Type and grade of Plastic.
Boss wall thickness to withstand installation forces and maximise performance.
Installation depth
Required application and strip out performance.
For advice, please contact our Applications Engineering Department with your specific requirements