Laboratory Reactors0 pages
Autoclave Engineers
Providing Tools for Research and Industry
1,000 ml Bolted Closure
Stirred Reactor
At a Glance
Volume: 1,000 ml
Vessel MAWP: 5,500 psi @ 650° F
(Design Pressure) (379 Bar @ 343° C)
Material of Construction: 316 Stainless Steel or
HASTELLOY® C-276
Principle of Operation
The Autoclave Engineers’ Bolted Closure Reactor has been
designed for reliable high pressure operation. The seal is a
metal gasket machined from the same material as the vessel.
Many combinations of standard components are available.
The cover of the unit remains fixed in the stand to permit
opening of the vessel without disassembling any process
connections. The body is easily removed and drops away
from the cover.
General Specifications
Maximum Allowable Working Pressure (MAWP)
5,500 psi @ 650° F*
(379 Bar @ 343° C)*
Minimum Design Metal Temperature (MDMT)
-20° F @ 5,500 psi
(-29° C @ 379 Bar)
Maximum Recommended Operating Pressure (MROP)
varies based on gauge, transducer, and rupture disk selection.
Refer to Ordering Guide for Details.
Critical Dimensions: 1,000 ml
Inside Diameter: 3.0” (76 mm)
Straight Wall: 8.71” (221 mm)
Approximate
Dimensions: Tall Bench Top Floor Stand
Overall Height** 39.4” (1002 mm) 61.8” (1570 mm)
Width: 20.5” (522 mm) 25.0” (635 mm)
Depth: 26.2” (665 mm) 26.5” (665 mm)
* 650° F (343° C) rating is vessel mean wall temperature. Actual Process temperature will be lower.
** Overall height based on belt driven units. For actuals see standard drawings. 1,000 ml Bolted Closure Reactor Internals
Stirred Reactors
Connection Schedule
All of the connections shown will be provided. For any accessories not ordered, the corresponding connection will be plugged.
All connections at cover are AE high temperature F437 Flat Bottom adapted to the “Topside Of Cover” connection listed below.
“A” Charging Port 0.375” port 3/8” O.D. tube Cover top 0.25”
“B” Gas Inlet 3/16” O.D. tube 1/8” O.D. tube Cover side 0.062”
“C” Sparge Tube† 3/16” O.D. tube 1/8” O.D. tube Cover side 0.031”†
“D” & “H” Cooling Coil 3/16” O.D. tube 1/4” O.D. tube Cover side 0.125”
“E” Vent and Pressure Indication Branched into “F” 1/8” O.D. tube Cover side 0.062”
“F” Safety Head 0.187” port 1/8” FNPT Cover top 0.187”
“G” Thermowell‡ 1/8” O.D. tube 3/32” Port‡ Cover top N/A
“J” Blow Pipe 3/16” O.D. tube 1/8” O.D. tube Cover side 0.062”
“K” Liquid Sample 3/16” O.D. tube 1/8” O.D. tube Cover side 0.062”
“L” MagneDrive® Agitator 1/2” O.D. Mixing Shaft MagneDrive® Cover top N/A
Opening
Label
Purpose Opening or feature
description on
underside of cover
Opening or feature
description on topside
of cover
Entry Point Smallest diameter
orfice (nominal)
in flow path
† The tube that forms the sparge tube is 3/16” O.D. and 1/8” I.D. with a plug in the end. Nine .031” diameter holes are drilled in the sparge ring to bubble gas into the reactor.
‡ The tube that forms the thermowell is 1/8” O.D. and 1/16” I.D. with a plug in the end. A 3/32” port is drilled in the cover to guide the thermocouple to the opening in the thermowell.