MM-1 Programmable Pipe Cutter0 pages
MM-1 Programmable Pipe Cutter - Programming
Capabilities
TYPE 1
SADDLE
NOZZLE
CUTS
TYPE 2
OFFSET
SADDLE
NOZZLE
CUTS
(Hillside)
TYPE 3
LATERAL
NOZZLE
CUTS
Computer Software
The MM-1 Programmable Pipe Cutter can be
programmed from a PC, using either of two
software packages described below. Shapes
can be created off-line, and downloaded to the
machine when required. A cable is supplied to
connect to the serial or USB port of the PC.
TYPE 4
MITER CUT
1. PC Option / BUG-6140.
This runs under Windows, and allows you to:
t • Create shapes on the PC.
t • tSave any number of shapes to disk, and
tt retrieve them as necessary.
t • View a programmed shape on screen tt which helps program verification.
t •tDownload programmed shapes from the
tt PC to the machine.
TYPE 5
HOLE CUTTING AT
VARIOUS ANGLES
2. BUG-6240 CAD Interface.
This is a complete package that includes both
the PC option and DeskCNC. This will allow
you to take two dimensional CAD drawings
and convert them to Shape files that you can
directly load into your shape machine.
t •tDeskCNC is used to modify two tt
tt dimensional CAD drawings (.DXF files)
tt and create a toolpath
t •tThe toolpath is saved as a CNC file
tt using DeskCNC
t •tThe CNC file can be loaded in the PC
tt option for easy integration with the MM-1
SHAPE PROGRAM
CUSTOM
IRREGULAR
SHAPES
MM-1 Programmable Pipe Cutter - Accessories
CWO-7598 Powermax 85
Includes the following:
•t Interface cable to the MM-1 Pipe Cutter
•t 50' (15.24 m) Machine Barrel Torch
Power Requirements:
Auto voltage runs on 200-600 Volts, 1 or 3-phase,
without the need of rewiring.
MM-1
ECONOMICAL, AUTOMATED PIPE CUTTER
SAVES LAYOUT AND FIT-UP TIME.
Adjustable Output Current: 25-85 Amps
Cutting Capacity: (Recommended) 3/4" (19 mm)
BUG-1274
3-Hose Machine Torch 10"
(254 mm) Cutting Torch is
the same for AcetylenePropane-Natural Gas. Only
the tip changes.
Oxy-Acetylene Tips
Programming
Arbitrary Shapes
TIME
DELAY
PERCENT
SPEED
WAIT FOR AUXILIARY
START
MODES
BUTTON
WELD/OXY PIPE CUT
NUMBER
OFF
REPEAT
WELD/OXY ANOTHER
ON
STEP
5
For custom shapes, select the
“shape” software. Programming
is simple, but will require a
few more steps due to all the
variations possible.
First, the developed pattern
should be laid out as if the pipe
is unrolled flat. The cut is then
split into a sequence of straight
lines or circular arcs that make
up the desired pattern.
Next, these should be listed
in a table on paper, with the
type, quadrant and required
dimensions (referring to the chart
in the Instruction Manual).
To program the shape, press
“A”, then enter the total
segments at the prompt.
Next, enter the data for each
segment type, quadrant and
dimensions in turn, at the
prompt. When all segments
are entered the program is
ready to run.
Part No.t
Tip Sizet
Plate Thicknesst
Oxygen PSIGt Fuel Gas PSIG t
Orifice Drill Size
BUG-1270-000t
000t
Light Gauge to 3/16t
15-20t
5-15t
#68
BUG-1270-00t00t
3/16-3/8t
20-25t
5-15t
#64
BUG-1270-0t0t 3/8-5/8t
35-40t 5-15t
#60
BUG-1270-1t1t
5/8-1t
35-40t 5-15t
#56
BUG-1270-2t2t
1-2t
40-45t 5-15t
#52
BUG-1270-3t3t
2-3t
45-50t 5-15t
#48
BUG-1270-4t4t
3-6t
50-75t 10-15t
#42
* For tips to cut 6" to 15", please consult factory.
Oxy-Propane, Natural Gas Cutting Tips
Part No.t
Tip Sizet
Plate Thicknesst
Oxygen PSIGt Fuel Gas PSIG t
Orifice Drill Size
BUG-4070-000t
000t
Light Gauge to 3/16t
15-30t
5-15t
#68
BUG-4070-00t00t
3/16-3/8t
20-30t
5-15t
#64
BUG-4070-0t0t 3/8-5/8t
30-40t 5-15t
#60
BUG-4070-1t1t
5/8-1t
35-50t 5-15t
#56
BUG-4070-2t2t
1-2t
40-55t 5-15t
#52
BUG-4070-3t3t
2-3t
45-60t 5-15t
#42
BUG-4070-4t4t
3-6t
50-75t 5-15t
#42
BUG-4070-5t5t
6-8t
65-80t 5-15t
#35
BUG-4070-6t6t
8-12t
70-90t 5-15t
#30
Bug-O Systems
Automated Cutting and Welding Systems
412-331-1776twww.bugo.com
A QUALITY PRODUCT FROM BUG-O SYSTEMS • 280 TECHNOLOGY DRIVE • CANONSBURG, PA 15317-9564 USA
A DIVISION OF WELD TOOLING CORPORATION © Weld Tooling Corp.
ROM 1:16 Litho in U.S.A. LIT-MM1-BRO-0612
Bug-O Systems is guided by honesty, integrity and
ethics in service to our customers and in all we do.