B 200 pages

®

Industrial controllers

1/310

Palm grip B 20

2013

The Palm grip B 20 is an actuating element for our multi-axis controller V 8, VV 8, V 85, VV 85,
V6, VV6. It can also be used as an actuating element for hydraulic drives.
Push buttons, rocker switches, etc. can also be fitted to suit appropriate requirements
The palm grip has a highly flexible wire 0,1 mm2 x 450 mm long.
The mounting piece for the drive rod can be supplied with a tapped hole 12 mm.
The palm grip B 20 is made of PAGF35 plastic and is black in colour.
Contact complement 0,5 A 110 V AC 15 or 1,5 A 24 V DC 13
I min > 0,2 mA 2 V DC 12 Gold plated for max. load of 0,12 Watt (standard)
Micro change over contacts available on request

1

permissible ambient temperature

operating
storage

climate resistance
damp heat constant
damp heat cyclic
degree of protection front

-40° C to +60° C
-50° C to +80° C

IEC 60068-2-78
IEC 60068-2-30
IP 65 IEC/IEN 60529

Type B 20

Contactcomplement

Pos.
1

Palm grip with mounting piece for control handle
with hand rest left or right

2

Push button
colour red RD, black BK, yellow YE, green GN, blue BU
Push button
colour red RD, black BK, yellow YE, green GN, blue BU

Weight
gramm

3

Type
B 20

1 normally open

20

D

KDA21

1 NO 0,1 A 24 V DC 13

20

D

KEM 59

2 normally open
30
30
30
30
30
30

W
W
W
W
W
W

30
30

K
KT

70

PA 9

8
8.1
8.2
8.3
8.4
8.5
8.6

Rocker switch
Rocker switch
tip-0-tip
Rocker switch
0-tip
Rocker switch rest-0-tip
Rocker switch rest-0-rest
Rocker switch
0-rest
Rocker switch rest - rest

11
12

Lever switch
Cross switch tip-0-tip
T-O-T / T-O-T
color red RD, black BK, grey GR

14

Drive with potentiometer PA9, actuating by rotary mechanism
1 wire-wound potentiometer T… 5 kOhm 2 Watt

17

Drive with Hall sensors HA 11, actuating by rocker wheel installed with spring
return in centre position, with electronic redundant Voltage output impressed
Power supply 4,6-5,5 Volt output 0,5-2,5-4,5 Volt +5 mA output characteristic linear

90

HA 11

18

Drive with potentiometer PA 12, actuating by rocker wheel installed with
spring return in centre position, 1 conductive plastic potentiometer T 375 with
centre tap 107 switching cycles, resistance 2 x 5 kOhm 0,5 Watt
wiper current max 1 mA, 2 direction contacts

90

PA 12

19

Drive with Hall sensors HA 12, actuating by rocker wheel installed with spring
return in centre position, with electronic redundant Voltage output impressed
Power supply 4,6-5,5 Volt output 0,5-2,5-4,5 Volt +5 mA output characteristic linear

90

HA 12

21

Drive with Hall sensors HA 13, actuating by rotating palm grip left resp. right
with spring return in centre position, with electronic redundant Voltage output
impressed Power supply 4,6-5,5 Volt output 0,5-2,5-4,5 Volt +5 mA
output characteristic linear

90

HA 13

T-0-T
0-T
R-0-T
R-0-R
0-R
R - R

22

Bellow for palm grip B 20 (Part-no.: 5209900402)
required for multi-axis controller V 8, VV 8, V 85, VV 85
Bellow for palm grip B 20 (Part-no.: 5209900577)
required for multi-axis controller V 6, VV 6
Front plate with 4 screws M5 x 15 (for mounting the bellow)
required for bellow KMD 229
Rubber cap protection IP 67 for push button Pos. 2
color red RD, black BK, yellow YE, green GN, blue BU

31
32
33

98

KBAD 670

2 normally open

Vibrator button actuating through solenoid 24V DC
impulse signal 100% duty cycle (e.g. indication of cable movement)

30

1 normally open
4 normally open

Multi-axis controller V 21 look Catalog 1/146

25

T4

V 21
60
KMD 109
KMD 229
KBF 905
KMD 179

60

V

Pice
EURO