OMAX® 120X JetMachining® Center Series0 pages

PRECISION ABRASIVE WATERJET SYSTEMS
Equipment Specifications
120X Series
The OMAX Technology Guarantee entitles you, as the original owner, to free OMAX software upgrades for the life of the machine.
Connect and follow OMAX for the latest news
in waterjet technology.
Standard Features
• OMAX Intelli-MAX® software offers higher average cutting speeds and greater precision with free upgrades
for the life of the machine
• Programmable Motorized Z-Axis
with precision OMAX MAXJET®5i Nozzle Assembly
• Intelli-TRAXTM traction drive system and linear encoder completely enclosed inside covers on both the X and Y-axis
• Scissor-style hard plumbing
• Component protection against water, dirt, and grit
• High efficiency standard direct drive pump systems available in 30 and
40 hp options with pressures up to 55,000 psi. EnduroMAXTM Pump
available in 30, 40, or 50 hp options. Both standard and EnduroMAX pumps are available in a DualPUMP Package.
• Rapid Water Level Control for quiet
and clean submerged cutting
• Bulk Abrasive Feed Assembly trans-ports garnet from the assembly’s large hopper into the small hopper located
at the Z-axis
• Solids Removal System (SRS) designed for tough industrial use (available as
an option)
• Tilt-A-Jet® taper compensating abra-
sivejet cutting head (available as an
option)
• Shipped as a completely pre-
assembled and factory-tested system
Abrasivejet Benefits
• Machines a wide range of materials
and thicknesses
• Does not create heat-affected zones
or mechanical stresses
• Rapid setup, no tool changes required
• Minimal fixturing required
• Leaves behind a satin-smooth edge,
reducing secondary operations
• No noxious gases, liquids or oils
used in (or caused by) the machining
process
• Completes most work below 80 dBA
at 1 meter for submerged cutting
• Environmentally “green” system
with quiet and clean operation, low electrical and abrasive consumption
Machine Dimensions
Footprint (with controller) 260" x 207" (6,604 mm x 5,258 mm)
Weight (tank empty) 12,000 lbs (5,443 kg)
Height (with scissor plumbing) 168" (4,267 mm)
Operating Weight 48,630 lbs (22,060 kg)
Work Envelope
X-Y Cutting Travel 160" x 120" (4,064 mm x 3,048 mm)
Table Size 182" x 137" (4,623 mm x 3,480 mm)
Material Support Slats 4" x 1/8" Galvanized Steel
Maximum Supported
Material Load 400 lbs/sq ft (1,950 kg/sq meter)
(Optional accessories may reduce travel. Contact OMAX for information.)
OMAX® 120X/S JetMachining® Center
For additional OMAX 120X Models with increased capacity, see reverse side.
Machine Dimensions
Footprint (with controller) 340" x 207" (8,636 mm x 5,258 mm)
Weight (tank empty) 15,000 lbs (6,803 kg)
Height (with scissor plumbing) 168" (4,267 mm)
Operating Weight 61,000 lbs (27,669 kg)
Work Envelope
X-Y Cutting Travel 240" x 120" (6,096 mm x 3,048 mm)
Table Size 259" x 137" (6,579 mm x 3,480 mm)
Material Support Slats 4" x 1/8" Galvanized Steel
Maximum Supported
Material Load 400 lbs/sq ft (1,950 kg/sq meter)
(Optional accessories may reduce travel. Contact OMAX for information.)
OMAX 120X JetMachining Center
Machine Dimensions
Footprint (with controller) 420" x 230" (10,668 mm x 5,842 mm)
Weight (tank empty) 20,000 lbs (9,072 kg)
Height (with scissor plumbing) 168" (4,267 mm)
Operating Weight 81,897 lbs (37,148 kg)
Work Envelope
X-Y Cutting Travel 320" x 120" (8,128 mm x 3,048 mm)
Table Size 342" x 137" (8,687 mm x 3,480 mm)
Material Support Slats 4" x 1/8" Galvanized Steel
Maximum Supported
Material Load 400 lbs/sq ft (1,950 kg/sq meter)
(Optional accessories may reduce travel. Contact OMAX for information.)
120X Series
C o r p o r a t i o
n
OMAX 120X-1 JetMachining Center